Crown Audio DCi 4/300DA DriveCore Install DA Serie

The Crown DCi 4/300DA DriveCore Install DA Series is a 4-channel power amplifier with Dante / AES67 networked audio and integrated DSP The amplifier is capable of producing 300W of output per channel and works with 2- - 4- - 8- - and 16-Ohm speakers or with 70/100Vrms systems Channels can be bridged for powering higher power applications such as a subwoofer The amp's advanced capabilities and support for Dante Domain Manager makes it well suited for installations that are standardized on Dante for networked audio transport The Dante / AES67 ports provide primary and secondary connections for redundancy and will accept 48 and 96 kHz digital audio Analog audio can be sent via Dante / AES67 pre/post processing (at 48 kHz) Network configuration - monitoring - and control are provided with HiQnet protocols over standard TCP/IP network connections The HiQnet Audio Architect software allows for remote configuration - monitoring - and control of all aspects of the DCi-DA Series amplifiers Additionally - a programmable General Purpose Input/Output (GPIO) port can be configured to control volume - recall presets - report errors to a third-party control system - and more The integrated DSP provides a comprehensive set of tools and features including LevelMAX limiting for inputs and outputs with thermal limiting - input compression - input & output delay (up to 2 seconds) - input & output EQ - crossover settings - and a signal generator The Crown DCi 4/300DA DriveCore Install DA Series 4-Channel Amplifier ships with four input connectors and a power cord

Features: Onboard Digital Signal Processing (DSP), Limiters, Compressor, Delay, EQ, XOver, Programmable General Purpose I/O Port, 300W per Channel, 70V/100V Compatible, Bridgeable Channel Pairs, Front Panel Indicators, Integrated Dante / AES67 Network Audio, Network Configuration, Monitor & Control, Continuous Load Monitoring

Inputs: 3-pin block connectors

Outputs: Terminal strips

Output Power: Dual Mode: @ 2 Ohms: 150 W (Per Channel) @ 4 Ohms: 300 W (Per Channel) @ 8 Ohms: 300 W (Per Channel) @ 16 Ohms: 150 W (Per Channel) @ 70 Vrms: 300 W (Per Channel) @ 100 Vrms: 300 W (Per Channel) Bridge Mono Mode: @ 4 Ohms: 300 W @ 8 Ohms: 600 W @ 16

Voltage Gain: 34 dB

Frequency Response: 20 Hz to 20 kHz (8 Ohms): ±0.25dB

Signal to Noise Ratio: Signal to Noise Ratio (ref. rated power - (8 Ohms - 20 Hz to 20 kHz): > 108 dB

Total Harmonic Distortion: < 0.35% (@ full-rated power - from 20 Hz to 20 kHz)

Intermodulation Distortion: ≤ 0.35% (60 Hz and 7 kHz @ 4:1 - from -30 dB to full-rated power)

Damping Factor: > 1000 (20 to 100 Hz)

Crosstalk: > 80 dB (below rated power - 20 Hz to 1 kHz)

CMRR: > 70 dB (20 Hz to 1 kHz - typical)

DC Output Offset: ±10 mV (with inputs shorted)

Input Impedance: 10 kOhms (nominally balanced) 5 kOhms (nominally unbalanced)

Maximum Input Level: +20 dBu (before compression) +26 dBu (before clipping)

Required AC Mains: 100 to 240 VAC - 50/60 Hz (±10)

Power Connector: 15 A IEC

Cooling: Continuously variable-speed forced air - front-to-back airflow

Load Impedance: Stereo/Dual Mode: 2 to 16 Ohms - 70 Vrms - 100 Vrms Bridged Mono: 4 to 16 Ohms - 140 Vrms - 200 Vrms

Fan Noise Level: 45

Dimensions: 14.3-inch / 36.2 cm

Weight: 20.1 lb / 9.1 kg